Peerless Industries Indoor Furnishings DS508 User Manual

Installation and Assembly:  
Model: DS508  
Maximum Load Capacity:  
200 lb (90.7 kg)  
ISSUED: 03-05-09 SHEET #:125-9054-2 07-15-09  
For customer care call 1-800-865-2112 or 708-865-8870.  
 
Before you begin, make sure all parts shown are included with your product.  
Parts may appear slightly different than illustrated.  
A
Parts List  
Description  
A wall plate  
Qty. Part #  
1
1
4
4
4
4
4
4
4
4
2
4
1
6
145-1054  
B adapter plate  
145-1052  
5S1-015-C03  
590-0097  
520-1068  
504-9013  
520-1027  
520-1128  
520-9262  
540-1001  
570-1029  
560-9711  
560-9646  
520-9521  
C
#14 x 2.5" wood screw  
D concrete anchor  
E
F
G
H
I
M8 x 15 mm socket pin screw  
M4 x 12 mm phillips screw  
M5 x 12 mm phillips screw  
M6 x 12 mm phillips screw  
M10 x 15 mm socket screw  
#8 SAe flat washer  
J
K
L
M
N
O
3/4" x 3/16" x 10" adhesive strip  
cable tie  
4 mm security allen wrench  
1/4-20 x 2.5" phillips screw  
1/4" SAe washer  
10 540-9440  
560-9708  
P toggler  
6
E
C
D
G
F
B
J
I
H
L
K
M
P
O
N
ISSUED: 03-05-09 SHEET #:125-9054-2 07-15-09  
For customer care call 1-800-865-2112 or 708-865-8870.  
3 of 9  
 
Installation to Double Wood Stud Wall  
WARNING  
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all  
attached hardware and components.  
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the  
screws, greatly reducing their holding power.  
• Never tighten in excess of 80 in. • lb (9 N.M.).  
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder  
is highly recommended.  
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-  
ers are responsible to provide hardware for other types of mounting situations.  
Wall plate (A) can be mounted to two studs that are 16" apart. Use a stud finder to locate the edges of the studs.  
Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down  
each stud’s center. Place wall plate on wall as a template. Level plate, and mark the center of the four mounting  
holes. Make sure that the mounting holes are on the stud centerlines. Drill four 5/32" (4 mm) dia. holes 2-1/2"  
(64 mm) deep. Make sure that the wall plate is level, secure it using four #14 x 2.5" wood screws (C) as shown.  
1
Skip to step 2  
A
STUD  
C
ISSUED: 03-05-09 SHEET #:125-9054-2 07-15-09  
For customer care call 1-800-865-2112 or 708-865-8870.  
4 of 9  
 
Installation to Solid Concrete or Cinder Block  
WARNING  
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete  
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid  
part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifica-  
tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to  
avoid breaking out the back of the hole when entering a void or cavity.  
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.  
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-  
ware and components.  
Make sure that wall plate (A) is level, use it as a  
fig. 1.1  
1
template to mark four mounting holes. Drill four 1/4"  
(6 mm) dia. holes to a minimum depth of 2.5"  
(64 mm). Insert anchors (D) in holes flush with wall as  
shown in figure 1.2. Place wall plate over anchors and  
secure with #14 x 2.5" screws (C). Level, then tighten  
all fasteners.  
solid concrete  
cinder block  
D
Skip to step 2  
A
WARNING  
• Tighten screws so that wall plate is firmly attached,  
but do not overtighten. Overtightening can damage  
screws, greatly reducing their holding power.  
• Never tighten in excess of 80 in. • lb (9 N.M.).•  
Always attach concrete anchors directly to load-  
bearing concrete.  
C
• Never attach concrete anchors to concrete covered  
with plaster, drywall, or other finishing material. If  
mounting to concrete surfaces covered with a finish-  
ing surface is unavoidable, the finishing surface must  
be counterbored as shown below. Be sure concrete  
anchors do not pull away from concrete when tight-  
ening screws. If plaster/drywall is thicker than 5/8",  
custom fasteners must be supplied by installer.  
fig. 1.2  
concrete surface  
1
D
INCORRECT  
CORRECT  
concrete  
wall  
plate  
wall  
plate  
Drill holes and insert anchors (D).  
concrete  
A
C
2
plaster/  
drywall  
plaster/  
drywall  
D
Place plate (A) over anchors (D) and secure with screws (C).  
3
Tighten all fasteners.  
ISSUED: 03-05-09 SHEET #:125-9054-2 07-15-09  
For customer care call 1-800-865-2112 or 708-865-8870.  
5 of 9  
 
Installation to Metal Studs  
WARNING  
• Drywall must be 1/2" or thicker, and metal stud must be 24 gauge or thicker.  
• Make sure that the wall will safely support the combined load of the equipment and all attached hardware and  
components.  
• Make sure that togglers are anchored into the center of the studs. The use of an "edge to edge" stud finder is highly  
recommended.  
Using a stud finder, locate and mark the edges of the metal stud used in mounting this product. Use of an edge  
to edge stud finder is highly recommended. Use a level to draw a level, vertical line down the center of the stud.  
Level wall plate, and mark the center of the six mounting holes. Make sure that the mounting holes are on the stud  
centerlines. Drill two 1/2" holes through drywall and metal studs. NOTE: It may be necessary to drill 5/32" pilot  
holes prior to drilling 1/2" holes. Install togglers (P) as shown in figure 1.3. Loosely fasten wall plate to wall using six  
1/4-20 x 2-1/2" screws (N) and six 1/4" washers (O) as shown in figure 1.4. Level, hold, and then tighten all screws.  
1
fig. 1.3  
1
drill  
1/2"  
hole  
O
Pivot end of toggler (O).  
2
fig. 1.4  
O
P
A
Push into hole.  
O
3
N
O
Rotate toggler (O) clockwise to wedge it  
against inside walls of metal stud.  
4
O
Slide plastic cap forward while pulling back  
firmly on ring.  
5
O
Break off excess.  
ISSUED: 03-05-09 SHEET #:125-9054-2 07-15-09  
For customer care call 1-800-865-2112 or 708-865-8870.  
6 of 9  
 
Placement of Adhesive Strips  
Place adhesive strips (K) on the wall plate (A) in location that will allow the most contact with CPU.  
2
Note: Placement of adhesive strips will vary depending on size of CPU as shown in figure 2.2  
fig. 2.1  
fig. 2.2  
A
Placement of adhesive  
Placement of adhesive  
strips (K) for larger CPU's  
strips (K) for smaller CPU's  
K
Attach CPU to Wall Plate  
NOTE: Safety belt may need to be loosened to attach CPU to wall plate (A).  
3
Press CPU against adhesive strips on wall plate and tightly secure safety belt against CPU.  
CPU  
A
SAFTEy  
STRAP  
ISSUED: 03-05-09 SHEET #:125-9054-2 07-15-09  
For customer care call 1-800-865-2112 or 708-865-8870.  
7 of 9  
 
Attaching Adapter Plate to Screen  
fig. 4.1  
Attaching adapter plate to screen with  
SCreeN  
4
VESA hole pattern:  
Choose hole pattern and fasteners shown in detail 2 for  
mounting screen with VESA mounting patterns. Hand thread  
screws (F, G or H) through washers (J or O) and adapter  
plate (B) into screen as shown in figure 4.1. Screw must  
make at least three full turns into the mounting hole and fit  
snug into place. Securely tighten screws.  
B
WARNING  
• If screws don't get three complete turns in the screen  
inserts or if screws bottom out and bracket is still  
not tightly secured, damage may occur to screen or  
product may fail.  
F, G or H  
J or O  
MOUNTING PATTERNS  
VESA® 200 x 100  
VESA® 100 x 100  
VESA® 200 x 200  
M4 x 12 mm screws (F) with #8  
washers (J) or M5 x 12 mm screws  
(G) with 1/4" washers (O)  
M4 x 12 mm screws (F) with  
washers (J), M5 x 12 mm screws (G)  
or M6 x 12 mm screws (H)  
M5 x 12 mm screws (G) or  
M6 x 12 mm screws (H) with  
1/4" washers (O)  
with 1/4" washers (O)  
DETAIL 2  
Attaching adapter plate to dedicated adapter plates:  
Using the hole pattern shown in detail 3, attach the adapter plate (B) to dedicated adapter plate with four  
M10 x 15 mm screws (I) as shown in figure 4.2. Tighten screws using 6 mm allen wrench (not included).  
MOUNTINg PATTerN fOr  
DEDICATED ADAPTER PLATES  
fig. 4.2  
DEDICATED  
ADAPTER PLATE  
B
I
DETAIL 3  
ISSUED: 03-05-09 SHEET #:125-9054-2 07-15-09  
For customer care call 1-800-865-2112 or 708-865-8870.  
8 of 9  
 
Attaching Adapter Plate to Wall Plate  
Thread two M8 x 15 mm screws (E) into bottom holes of wall plate (A) leaving 1/8" space between head of screw  
and wall plate as shown in figure 5.1. guide hook slots of adapter plate (B) onto screws (E), while supporting  
weight of screen, align top holes of wall plate and adapter bracket to the desired tilt angle and secure with two M8 x  
5
15 mm screws (E). Tighten all screws securely.  
fig. 5.1  
10° TILT  
5° TILT  
fig. 5.2  
NO TILT  
A
HOOK  
SLOTS  
E
1/8"  
E
A
B
BOTH  
SIDES  
E
WALL NOT SHOWN fOr CLArITy  
Accessing CPU  
Loosen top two M8 x 15 mm screws (E) 1/4 turn and temporarily remove bottom two M8 x 15 mm screws (E) on  
adapter plate (A) as shown in figure 6.1. Swing screen forward and swing support brackets downward into adapter  
plate (B) to brace screen in open position as shown in figure 6.2.  
6
fig. 6.1  
fig. 6.2  
LOOSeN 1/4 TUrN ON  
E
BOTH SIDeS  
A
B
B
A
SUPPOrT BrACKeTS  
(BOTH SIDeS)  
reMOve  
E
ISSUED: 03-05-09 SHEET #:125-9054-2 07-15-09  
9 of 9  
For customer care call 1-800-865-2112 or 708-865-8870.  
© 2008, Peerless Industries, Inc. All rights reserved.  
All other brand and product names are trademarks or registered trademarks of their respective owners.  
 

Peavey Power Supply Mark VIII User Manual
Philips Car Satellite TV System HFL3008D User Manual
Philips Car Video System 150MT2 User Manual
Philips DVD Player MDV450 User Manual
Philips Portable Speaker SBA161 User Manual
Philips Stereo System SWA3302S User Manual
Philips TV Cables SWA2523 User Manual
Philips TV DVD Combo 28PW6818 User Manual
Pioneer TV DVD Combo DVD V630 User Manual
Presonus Audio electronic Recording Equipment PreSonus 2008 User Manual